
Recently, a research team from the Department of Advanced Laser and Optoelectronic Functional Materials and the Department of Airborne Laser Technology and Systems, Shanghai Institute of Optics and Precision Machinery, Chinese Academy of Sciences, has made progress in the research of high-performance ceramic phosphors applied in white light LED/LD illumination, and the relevant results are summarized in the title of "Investigation of a thermally robust orange-red MgO-YMASG: Ce composite phosphor ceramic for white light LED/LD illumination" and "Fabrication of Al2O3 Ce: (Y, Tb)3(Al, Mn)5O12 composite ceramic phosphors for high color rendering white LED/LD illumination" and 'Fabrication of Al2O3-Ce: (Y, Tb)3(Al, Mn)5O12 composite ceramic phosphors for high color rendering white LED/LD illumination' have been published in the Journal of Alloys and Compounds and Optical Materials, respectively.
In recent years, fluorescence-converted white light-emitting diodes (WLEDs) and white laser diodes (WLDs) based on YAG: Ce phosphors have been widely used in the lighting and display fields due to their energy-saving, environmentally friendly, small size, and long service life. Among them, Ce: YAG fluorescent ceramics are considered to be an important fluorescent conversion material in WLED/WLD devices due to their high luminous efficiency, good chemical stability and relatively simple preparation process. However, as the operating power of blue LEDs and LDs increases, the YAG: Ce phosphor ceramics will suffer from thermal burst phenomenon and thus reduce their luminescence efficiency. Meanwhile, the lack of red component in the emission spectrum of YAG: Ce leads to its low color rendering index (CRI). Therefore, how to mitigate the thermal burst phenomenon and improve the luminescence performance of fluorescent ceramics under high power excitation have become two major challenges.

Fig. 1. Temperature-dependent trends of thermal diffusivity (a), specific heat capacity (b) and thermal conductivity (c) of MgO- YMASG: Ce composite phase phosphor ceramics

Fig. 2. White LED emission spectra (a), luminescence efficiency and color temperature (b) of MgO- YMASG: Ce phosphor ceramics, and white LD emission spectra (c) of 30 at% MgO sample
In [Journal of Alloys and Compounds 990, 174436 (2024)] this work, the research team successfully prepared MgO-Y3Mg2AlSi2O12: Ce composite-phase fluorescent ceramics by vacuum solid-phase sintering. It was demonstrated that MgO could coexist with the YMASG phase, and the introduction of MgO as the second phase effectively reduced the formation of Y4MgSi3O13 impurities. With the increase of MgO content, the thermal conductivity of the samples increased from 5.13 W/ (m∙K) to 8.96 W/ (m∙K), which effectively mitigated the thermal accumulation of the fluorescent materials under high-power blue LED/LD excitation. The luminescence efficiency of the samples was comparable to that of YMASG: Ce phosphor ceramics at a MgO content of 30 wt%. This indicates that MgO significantly improves the light extraction efficiency of the composite phosphor ceramics. The study suggests that MgO- YMASG: Ce composite phosphor ceramics are promising as red phosphor materials for high-power white LED/LD lighting applications.
In this work [Optical Materials 151, 115397 (2024)], the research team prepared Al2O3-Ce: (Y, Tb)3(Al, Mn)5O12 composite phase fluorescent ceramics by vacuum solid-phase sintering, and introduced Tb3+ to suppress the color temperature increase of the ceramics while doping Mn2+ to enhance its color rendering index. Tb3+ is introduced to inhibit the increase of color temperature, and the second phase of Al2O3 is introduced to alleviate the thermal burst phenomenon effectively. Under laser and LED excitation, the ceramics with 3 at% Ce3+ and 4 at% Mn2+ showed the highest CRI values. Among them, the CRI reached 75.6 under laser excitation and 81.3 under LED excitation.This work demonstrates that through component optimization, Ce-Mn-Tb co-doping can significantly enhance the color rendering index of composite-phase fluorescent ceramics and mitigate the phenomenon of color temperature rise, and these findings are of great significance for improving WLED/WLD lighting devices.

Fig. 3. WLED (a) and WLD (b)(c) performance of Al2O3-Ce: (Y, Tb)3(Al, Mn)5O12 composite-phase fluorescent ceramics based on 3 at% Ce3+ concentration





